题目内容（请给出正确答案）

[主观题]

请求权的权利人能够请求（)。A．法院保护B．义务人为一定行为C．义务人不为一定行为D．义务人为一定行

请求权的权利人能够请求()。

A．法院保护

B．义务人为一定行为

C．义务人不为一定行为

D．义务人为一定行为或不为一定行为

查看答案

如搜索结果不匹配，请联系老师获取答案

您可能会需要：

重置密码查看订单联系客服

安装上学吧APP，拍照搜题省时又省心！

更多“请求权的权利人能够请求（)。A．法院保护B．义务人为一定行为…”相关的问题

第1题

You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another s

witch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch？

A．Switch(config)# switchport trunk encapsulation isl

B．Switch(config)# switchport trunk encapsulation ietf

C．Switch(config-if)# switchport trunk encapsulation isl

D．Switch(config-if)# switchport trunk encapsulation ietf

E．Switch(config-if)# switchport trunk encapsulation dot1q

点击查看答案

第2题

Assuming the default switch configuration,which approach should you use to configure the extended vlan range（1006 through 4094) on a cisco catalyst 3750 series switch？（）

A. Configure the switch to be in VTP client mode.

B. Configure the switch to be in VTP domaint mode.

C. Configure the switch to be in VTP transparent mode.

D. Configure the switch to be in VTPv2.

点击查看答案

第3题

When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network, how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port？（）

A. by snooping the CoS marking on the incoming frames

B. by using RTP hello messages between the switch port and the Cisco IP Phone

C. by using CDP

D. by using DHCP snooping

E. by snooping the incoming 802.1Q VLAN tag

点击查看答案

第4题

When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network,how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port？（）

A. by snooping the CoS marking on the incoming frames

B. by using RTP hello messages between the switch port and the Cisco IP Phone

C. by using CDP

D. by using DHCP snooping

E. by snooping the incoming 802.1Q VLAN tag

点击查看答案

第5题

The network administrator has discovered that the power supply has failed on a switch in t

he company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network？（）

A.One router is running RIPv1.

B.RIP neighbor is 224.0.0.9.

C.The network contains a loop.

D.Network 10.10.1.0 is reachable.

点击查看答案

第6题

As a network administrator, you issue the interface auto qos voip cisco-phone command on a

port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）

A. using DHCP snooping

B. snooping the incoming 802.1Q VLAN tag

C. using CDP

D. snooping the CoS marking on the incoming frames

点击查看答案

第7题

Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software？（）

A. show port network

B. show running-config

C. show controllers Ethernet-controller

D. show interfaces

点击查看答案

第8题

The network administrator has discovered that the power supply has failed on a switch in t

he company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network？（）

A. Lower the bridge priority number.

B. Change the MAC address of the switch.

C. Increase the VTP revision number for the domain.

D. Lower the root path cost on the switch ports.

E. Assign the switch an IP address with the lowest value.

点击查看答案

第9题

在一台Cisco Catalyst 2950交换机上作如下配置：Switch # config terminalSwitch （config) # i

在一台Cisco Catalyst 2950交换机上作如下配置：

Switch # config terminal

Switch (config) # interface fastethernet 0/1

Switch (config-if) # switchport mode access

Switch (config-if) # switchport access vlan2

若要将fastethernet 0/1端口还原到默认配置状态，可以使用()命令。

A、Switch (config) # default fastethernet 0/1

B、Switch (config) # default interface fastethernet 0/1

C、Switch (config) # no fastethernet 0/1

D、Switch (config) # erase interface fastethernet 0/1

点击查看答案

第10题

For which of the following campus LAN Areas is the Cisco Catalyst 500 Series switch most suitable？（）

A．Access Area

B． Backbone Area

C． Core Area

D． Distribution Area

点击查看答案