题目内容（请给出正确答案）

[主观题]

劳务分包人在施工开始前向工程承包人提出安全防护措施，防护措施费用由（)承担。A．劳务分包人B．施

劳务分包人在施工开始前向工程承包人提出安全防护措施，防护措施费用由()承担。

A．劳务分包人

B．施工双方

C．工程承包人

D．施工单位

查看答案

如搜索结果不匹配，请联系老师获取答案

您可能会需要：

重置密码查看订单联系客服

安装上学吧APP，拍照搜题省时又省心！

更多“劳务分包人在施工开始前向工程承包人提出安全防护措施，防护措施…”相关的问题

第1题

Which three steps are used to configure IPv6 in JUNOS software？（）

A. Assign 128-bit router id.

B. Enable a routing instance.

C. Assign IPv6 addresses to interfaces.

D. Add IPv6 family support to interfaces.

E. Enable IPv6-capable routing protocol.

点击查看答案

第2题

Your company has an IPv6 network that has 25 segments. You deploy a server on the IPv6 net

work.You need to ensure that the server can communicate with all segments on the IPv6 network.What should you do？（）

A. Configure the IPv6 address as fd00::2b0:d0ff:fee9:4143/8.

B. Configure the IPv6 address as fe80::2b0:d0ff:fee9:4143/64.

C. Configure the IPv6 address as ff80::2b0:d0ff:fee9:4143/64.

D. Configure the IPv6 address as 0000::2b0:d0ff:fee9:4143/64.

点击查看答案

第3题

Which command must be globally enabled on a Cisco router to support IPv6？（）

A. ip routing ipv6

B. ipv6 unicast - routing

C. ipv6 routing

D. ip classless

E. ipv6 cef

点击查看答案

第4题

A new router, named TK1, is being installed. You wish to add this router to your existing

OSPF network. In doing so, you configure the following:TK1(config) router ospf 1TK1(config-router) network 10.10.10.0 255.255.255.0 area 0After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this？（）

A. The AS is not correctly configured

B. The network subnet mask is incorrectly configured

C. The network wildcard mask is configured incorrectly

D. The network number is not correctly configured

E. The process id is configured incorrectly

F. None of the above

点击查看答案

第5题

Your company has computers in multiple locations that use IPv4 and IPv6. Each location is

protected by a firewall that performs symmetric NAT. You need to allow peer-to-peer communication between all locations.What should you do？（）

A. Configure dynamic NAT on the firewall.

B. Configure the firewall to allow the use of Teredo.

C. Configure a link local IPv6 address for the internal interface of the firewall.

D. Configure a global IPv6 address for the external interface of the firewall.

点击查看答案

第6题

You work as a technician at TestKing. You are configuring a Cisco router. You want to configure the IP address on an interface.Which command should you use？（）

A. router(config-if)#ip address 142.8.2.1 subnet mask 255.255.252.0

B. router(config-if)#142.8.2.1 0.0.3.255

C. router(config-if)#ip address 142.8.2.1 255.255.252.0

D. router(config-if)#142.8.2.1 subnet mask 255.255.252.0

E. router(config-if)#ip address 142.8.2.1 0.0.3.255

F. router(config-if)#ip address 142.8.2.1 subnet mask /22

点击查看答案

第7题

You have just purchased a brand new router and wish to have the router prompt you through

the initial configuration commands. Which router mode does this describe？

A．ROM Monitor mode

B．SETUP mode