网络管理员使用 ip address 172.16.1.254 255.255.255.0 命令配置路由器 R1 上的接口 fa0/0。但是,当管理员发出 show ip route 命令时,路由表没有显示直连网络。此问题的可能原因是什么?
A.接口 fa0/0 未被激活
B.需要先保存配置
C.目的网络为 172.16.1.0 的数据包未被发送到 R1
D.IPv4 地址的子网掩码不正确
A.接口 fa0/0 未被激活
B.需要先保存配置
C.目的网络为 172.16.1.0 的数据包未被发送到 R1
D.IPv4 地址的子网掩码不正确
第1题
B、S 172.16.1.0 is directly connected, Serial0/0
C、C 172.16.1.0 [1/0] via 172.16.2.2
D、S 172.16.1.0 [1/0] via 172.16.2.2
第2题
R1#config
R1(config)# interface FastEthernet 0/1
R1(config-if)#ip address (1) (2)
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#ip dhcp pool vlan 3
R1(dhcp-config)#network 192.168.3.0 255.255.255.0
R1(dhcp-config)#default-router 192.168.3.254 255.255.255.0 ; (3)
R1(dhcp-config)#dns-server 192.168.2.1 ; (4)
R1(dhcp-config)#lease 0 8 0 ; (5)
R1(dhcp-config)#exit
R1(config)#ip dhcp pool vlan 4
R1(dhcp-config)#network (6) (7)
R1(dhcp-config)#default-router 192.168.4.254 255.255.255.0
R1(dhcp-config)#dns-server 192.168.2.1
R1(dhcp-config)#lease 0 8 0
R1(dhcp-config)#exit
R1(config)#ip dhcp excluded-address (8) (9)
R1(config)#ip dhcp excluded-address 192.168.3.254
//排除掉不能分配的IP 地址
R1(config)#ip dhcp excluded-address 192.168.4.254
R1(config)# (10) 192.168.3.0 255.255.255.0 FastEthernet0/1
//在以太网接口和VLAN3 间建立一条静态路由
第3题
R1 (config)# interface Serial 1/0
R1 (config-if)# ip address (3) 255.255.255..0 (设置串口地垃)
R1 (config-if) #no shutdown (开高串口)
R1 (config) #interface FastEthernet0/0
R1 (config-if) #ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
(3)
第4题
请阅读以下R1的配置信息,并补充【6】~【10】空白处的配置命令或参数。按题目要求完成R1的正确配置。
Router>enable
Router
Routerconfigure terminal
Router(config)
Router(config)hostname R1
R1(config)interface f0/1
R1(config-if)ip address 202.206.16.1 255.255.255.0
R1(config-if)no shutdown
R1(config-if)interfacef0/2
R1(config-if)ip adress 202.206.17.1 255.255.255.0
R1(config-if)no shutdown
R1(config-if)exit
R1(config)
R1(config)interface s1
R1(config-if)vlan ip adress 202.112.41.144 255.255.255.252
R1(config-if)bandwidth 【6】 配置带宽为2.048Mbps
R1(config-if)【7】 PPP 封装PPP协议
R1(config-if)noshutdown
R1(config-if)exit
R1(config-if)iproute 【8】 配置缺省路由
R1(config-if)router rip
R1(config-router)network 【9】 配置参与RIP的网络
R1(config-router)network 【10】 配置参与RIP的网络
R1(config-router)end
R1write
R1
第5题
Router>enable
Router
Routerconfigure terminal
Router(config)
Router(config)hostname R1
R1(config)interface f0/1
R1(config-if)ip address 202.206.16.1 255.255.255.0
R1(config-if)no shutdown
R1(config-if)interface f0/2
R1(config-if)ip address 202.206.17.1 255.255.255.0
R1(config-if)no shutdown
R1(config-if)exit
R1(config)
R : (config)interface s1
R1(config-if)ip address 202.112.41.144 255.255.255.252
R1(config-if)tandwidth 【 6 】 配置带宽为 2.04Mbps
R1(config-if) 【 7 】 PPP 封装 PPP 协议
R1(config-if)no shutdown
R1(config-if)exit
R1(config)iproute 【 8 】 配置缺省路由
R1(config)routenrip
R1(config-mote)retwork 【 9 】 配置参与 RIP 的网络
R1(config-mote)retwork 【 10 】 配置参与 RIP 的网络
R1(config-router)end
R1write
R1
第6题
根据网络拓扑和需求说明,完成路由器R1的配置。
R1(config)# interface Serial 1/0
R1(config-if)# ip address (3) 255.255.255.0 (设置串口地址)
R1(config-if)#no shutdown (开启串口)
R1(config)#interface FastEthernet0/0
R1(config-if)#ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
第7题
根据网络拓扑和需求说明,完成路由器R1的配置。
R1(config)# interface Serial 1/0
R1(config-if)# ip address (3) 255.255.255.0 (设置串口地址)
R1(config-if)#no shutdown (开启串口)
R1(config)#interface FastEthernet0/0
R1(config-if)#ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
第8题
A、定义了开始和结束公有 IP 地址的名为 corp 的 NAT 池
B、定义了受 NAT 影响的私有地址的名为 corp 的访问列表
C、定义了开始和结束公有 IP 地址的编号为 4 的访问列表
D、在连接到受 NAT 影响的 LAN 的接口上启用的 ip nat outside
E、已启用的、处于活动状态并由 R1 路由的名为 corp 的 VLAN
第9题
A、定义了开始和结束公有 IP 地址的名为 corp 的访问列表
B、定义了受 NAT 影响的私有地址的名为 corp 的访问列表
C、定义了开始和结束公有 IP 地址的编号为 4 的访问列表
D、定义了受 NAT 影响的私有地址的编号为 4 的访问列表
第10题
A、丢弃该数据包,因为路由表中未列出目的主机
B、查找 S0/1/0 接口的 MAC 地址以确定新帧的目的 MAC 地址
C、在转发该数据包之前递归查找 S0/1/0 接口的 IP 地址
D、将该数据包封装到适合该 WAN 链路的帧中,并将其从 S0/1/0 接口转发出去
为了保护您的账号安全,请在“上学吧”公众号进行验证,点击“官网服务”-“账号验证”后输入验证码“”完成验证,验证成功后方可继续查看答案!