![](https://lstatic.shangxueba.com/sxbzda/h5/images/m_q_title.png)
路由器Router2的各接口已启用MPLS协议进程。在路由器Router2特权模式下分别输入以下3条命令: ①sho
路由器Router2的各接口已启用MPLS协议进程。在路由器Router2特权模式下分别输入以下3条命令:
①show mpls ldp neighbor
②show mpls ldp discovery
⑧show mpls ldp bindings
请解释以上3条配置命令各自完成什么功能?
![](https://lstatic.shangxueba.com/sxbzda/h5/images/tips_org.png)
路由器Router2的各接口已启用MPLS协议进程。在路由器Router2特权模式下分别输入以下3条命令:
①show mpls ldp neighbor
②show mpls ldp discovery
⑧show mpls ldp bindings
请解释以上3条配置命令各自完成什么功能?
第1题
路由器Router2的各接口已启用MPLS协议进程。在路由器Router2特权模式下分别输入以下3条命令:
①show mpls ldp neighbor
②show mpls ldp discovery
⑧show mpls ldp bindings
请解释以上3条配置命令各自完成什么功能?
第2题
如图所示,配置了路由器相关接口网络协议地址,同时管理状态、物理状态和链路协议均为打开或启动状态(UP)时,路由器Router1和路由器Router2自动生成的路由表分别为:
A、路由器Router1: C 192.168.1.0/24 is directly connected, FastEthernet0/0 C 192.168.2.0/24 is directly connected, FastEthernet0/1 路由器Router2: C 192.168.2.0/24 is directly connected, FastEthernet0/1 C 192.168.3.0/24 is directly connected, FastEthernet0/0
B、路由器Router1: C 192.168.2.0/24 is directly connected, FastEthernet0/1 C 192.168.3.0/24 is directly connected, FastEthernet0/0 路由器Router2: C 192.168.1.0/24 is directly connected, FastEthernet0/0 C 192.168.2.0/24 is directly connected, FastEthernet0/1
C、路由器Router1: C 192.168.1.0/24 is directly connected, FastEthernet0/1 C 192.168.2.0/24 is directly connected, FastEthernet0/0 路由器Router2: C 192.168.2.0/24 is directly connected, FastEthernet0/0 C 192.168.3.0/24 is directly connected, FastEthernet0/1
D、路由器Router1: C 192.168.2.0/24 is directly connected, FastEthernet0/0 C 192.168.3.0/24 is directly connected, FastEthernet0/1 路由器Router2: C 192.168.1.0/24 is directly connected, FastEthernet0/1 C 192.168.2.0/24 is directly connected, FastEthernet0/0
第3题
下面是路由器Router2的配置命令列表,在空白处填写合适的命令/参数,实现Router2的正确配置。
Router2>en
Router2conf term
Router2(config)interface e0
Router2(config-if)ip address 192.1.0.65 255.255.255.192
Router2(config-if)interface s0
Router2(configr-if)ip address 192.200.10.6 255.255.255.252
Router2(config-if)end
Router2(config)router (8)
Router2(config-router)network (9) area 0
Router2(config-router)network (10) area 2
Router2(config-router)exit
Router2copy run start
第6题
A.配置过程中需要为路由器相关接口配置 IP 地址
B.路由器接口默认为禁用
C.需使用 no shutdown 命令启用路由器接口
D.每个 VLAN 的路由条目左边的字母 C。
第8题
A.在路由器上配置物理接口并启用路由协议
B.在路由器上创建VLAN并在交换机上定义端口成员分配方案
C.在交换机上创建VLAN,包含端口成员分配方案并在路由器上启用路由协议
D.在交换机上创建VLAN,包含端口成员分配方案并在路由器上配置与VLAN匹配的子接口
第9题
A.配置过程中需要为路由器相关接口配置 IP 地址
B.路由器接口默认为禁用
C.需使用 no shutdown 命令启用路由器接口
D.每个 VLAN 的路由条目左边的字母 C。
为了保护您的账号安全,请在“上学吧”公众号进行验证,点击“官网服务”-“账号验证”后输入验证码“”完成验证,验证成功后方可继续查看答案!